The secret to a dirty circuit board is to be aware of it
Circuit boards are the most popular components in the PC world.
But there are a lot of dirty circuits out there.
Here’s a list of the dirtiest parts of circuit boards.1.
Dirty solder sponge The easiest way to get dirty solder is to use an old sponge, such as a tin foil.
When you use this sponge, you can get a sticky, tacky residue that will eventually make you scratch your desk.
Use a cotton swab to wipe it off.2.
Dirty electrolytic capacitor This capacitor can be used to charge and discharge capacitors, but it also makes it a great source of grease.
When the capacitor is wet, it will stick to the PCB surface and will stick more.
When it dries, it can become a very sticky residue.
It’s best to get rid of this capacitor after you have charged and discharged a capacitor.3.
Dirty resistive componentThe resistive components are often used to make the plastic parts of your circuit boards, but they can also be a source of solder.
Make sure you are careful when touching or touching the components, as you can make them a source for corrosion.4.
Dirty capacitors These can also form a source to solder.
If you’re using a high-quality capacitor, you should use one with a ceramic base instead of a glass one.
You can also try a high quality capacitor that has been dipped in solder and let it sit for a few hours to make sure the metal is shiny and not too sticky.5.
Dirty componentsThe components that are not connected to any other part of the circuit board are often the easiest to clean.
Make the circuit boards as clean as possible and then wipe the parts clean.6.
Dirty wires If you are using a soldering iron, you need to be very careful when you are touching the wires.
Be very careful not to burn yourself on the wires when you clean them.7.
Dirty contacts This can happen if you are applying pressure to the contacts and not cleaning them.
If the contact is dirty, it may get into your solder sponge.8.
Dirty sockets If you have a socket that has metal in it, you might be able to get a solder residue or a bit of a smudge in it.
If that happens, you’ll need to clean the socket up to make it safe for soldering.9.
Dirty screwsThis is one of the easiest ways to get messy.
Make a clean socket with a metal base and use a screwdriver to remove the metal.
If it comes off, then you can take the screw and clean it up.10.
Dirty tracesThis is the last thing that you need.
Clean your traces with an old toothbrush.
You don’t want to leave residue that you will have to wipe off with a cloth.11.
Dirty power supplyThis is an extremely common source of corrosion in PC boards.
When a PC board has a power supply connected to it, there is usually solder on it.
Sometimes, there can also have been traces left on the solder.
Clean these traces and you’ll have a cleaner PC board.12.
Dirty connectorsThis can happen when you add new wires to a connector.
Make your connection clean and straight before you add a new wire.13.
Dirty pinsThis can also happen when adding new pins to a board.
Make any connections clean and clean before adding new wires.14.
Dirty heat sinksThis can be a good source of residue.
Use an old heat sink and clean up after using it.15.
Dirty fansThis can cause problems when the fans are not properly adjusted.
You need to make a clean connection before you start adding new fans.16.
Dirty heatsinksThese can also cause problems.
Make all connections clean before you use any heatsinks.17.
Dirty USB portsThe USB ports are often one of your first and most important connections.
Make certain that they are clean before making any changes to them.18.
Dirty SATA portsThe SATA ports are another common source for contamination.
Make these connections clean first.19.
Dirty PCIe power connectorsThis is also a common source.
Make them clean before inserting any power connectors.20.
Dirty HDMI cablesThis is a very common source, as most HDTVs are powered via HDMI.
Clean up the cables before adding any cables.21.
Dirty VGA cablesThis can occur when a VGA cable has been damaged.
Make each of the connections clean after you connect the cables.22.
Dirty SD cardsThis can have a very detrimental effect on your PC if you don’t properly clean the SD card before installing a new card.
Clean the SD cards before installing the new card, as they may not be clean.23.
Dirty video cablesThis may be a common cause of PCB contamination.
Clean all of the connectors before putting a new video cable on a PCB.24.
Dirty audio cablesThis means you need some